Bathroom Remodel: Part 5, DIY Exposed Conduit Light Fixture

Bathroom Remodel: Part 5, DIY Exposed Conduit Light Fixture

Be forewarned…this post is a long one!

So our light situation in the bathroom went from the 1980s “Hollywood” strip light fixture to industrial.  I was more than ready to get rid of that thing. However, what I did really like about it was the amount of light it provided, since it had six bulbs.  We also had a globe light over the toilet, so that brought it up to seven total.

Hollywood strip light

I knew I wanted to keep the same amount of light bulbs, since we had spent some money changing all of them over to LED bulbs last year. The question was how were we going to be able to do that.

I was eating my lunch in the basement of where I work one day, and realized that I really liked the lighting that was down there. This is what I was inspired by.  I started looking for other ideas on Pinterest and loved what I was seeing for exposed conduit lighting.  There’s some really cool stuff out there!Pipe lights at the capitol

I got busy, and started drawing ideas up for what I wanted (BTW, an artist, I am not, so don’t laugh).  I knew we could used the electrical box that was already over the toilet, and I knew I wanted to use all seven bulbs. proposed light drawing

Then we used fabric strips to lay it out on the floor, and for our electrician friend, Jimmy, to look at, since he would be installing it. You’ll have to excuse the mess, as it was in the middle of construction. The layout did change a couple of times until we came up with something we thought would work the best. mock up of light using fabric

After we met at Lowes to get all the parts, we came back home and created a diagram, complete with conduit length measurements. Really, the only requirement that I had was that I wanted one bulb to be in the middle of the mirror when it was done. We did decide the main trunk of the conduit should be bigger to accommodate the four cords that would be at the one end, so we got 1″ conduit for that section, and two octagonal boxes with a 2″ depth.Diagram for finished light

From there we were able to start putting it together.  Jimmy brought his compact band saw, and we laid out the items we needed.Band saw to cut conduit

Once the conduit was cut to the lengths on the diagram, they started assembling the fixture.Connectors, boxes, conduit

Double D and Jimmy knocked out the metal tabs where the connectors would be for each conduit pipe, attached them to the boxes, and then connected the conduit. The boxes are used for multiple conductor runs that are split into two or more directions to bring power to a number of lights, in this case.Electrical boxes and connectors

We got the main trunk line assembled and connected the other parts. The last thing Jimmy did was to use a conduit bender to create a dip for one piece of the conduit to cross the main trunk line. For this piece, we also had to have two elbows to create corners. Conduit cut and put together

To start painting, we followed the advice of Jimmy, and wiped down all of the pieces with denatured alcohol to get any coating off of the conduit.  That way, we hoped the paint would stick well. I then sprayed all of the pieces with Rustoleum’s primer, including the hangers, box covers, and nuts and bolts. I let that sit for a couple of days, and didn’t notice any primer peeling away, or cracking. Primer coat for EMT

I then gave everything a couple of coats of Rustoleum’s Oil Rubbed Bronze to match the sink legs, and shower fixtures.Rustoleum's Oil Rubbed Bronze

Finally, it was install day.  Jimmy removed the light fixture over the toilet, and used the wire there to start hooking everything up. Once the first part went up, he did reconnect the fixture so they would have some light in the bathroom while they worked.First part of conduit

The guys then screwed the conduit hangers into the ceiling using the larger size for the 1″ conduit in the main trunk line. conduit hangers installed

And started hanging the conduit…11/2

Once the conduit was up they could start with the lights.  We purchased seven Hemma lamp cords from IKEA, to go with the seven Ledare LED bulbs we already had. I’m not an electrician, so I’m not even going to try to explain all of the steps that this involved.  I do know Jimmy and Double D threaded each lamp cord through to leave about 6″ hanging outside of the ends of the conduit. wires being threaded for conduit light

And then somehow connected all seven cords to the main box…wire pulled through for light

And let there be light! Like a lot of light. I knew it would be a different type of light, since it’s directed down now, instead of out from the wall.  You can definitely still see your grey hair and wrinkles though:) Industrial conduit light finished

I did want to show a close up of the bent conduit, and what it ended up looking like.  It was hard to tell how it was going to look while it was laying on the concrete in the garage, but I think it definitely gives the fixture character, and I’m glad we went with it. bent conduit

I love this last picture of it.  I took this by practically laying on the ground under it.  I just love how it turned out, and I can honestly say that this fixture is one of a kind.  One last step I did was spray some ORB in a plastic lid, and touched up the paint on the hardware and pipe, just wherever they dinged it in the process of installing it. I am a bit worried about the conduit rusting from steam condensation, and I want to make sure I do everything I can to hold that off for a while.  Hopefully the paint will help with that!finished light against the ceiling

I have to give big props to Jimmy for being willing to take on one of my crazy ideas, and work with me to get it done. It turned out better than I even thought it would:)

Thanks for hanging in there till the end!


Check out the other Bathroom Renovation posts:

Bathroom Remodel: Part 1, Demo

Bathroom Remodel: Part 2, Shower Installation

Bathroom Remodel: Part 3, Drywall and Paint

Bathroom Remodel: Part 4, Luxury Vinyl Tile Flooring 

Bathroom Remodel: Part 6, DIY Sink from Typewriter Stand

Bathroom Remodel: Part 7, Mirror and Sconces

Linking up with:

Rustic & Refined

DD Button 250 PNG

Between Naps on the Porch


Domestically Speaking


Home Stories A-Z


A Stroll Thru Life


Grandma’s House DIY



6 responses »

  1. Great idea, Sarah/I have always liked the lighting in your bathroom/with the new install, you can certainly still see the gray hair and wrinkles, lol/Cool idea/always proud of your creativity and kudos to DD and Jimmy for seeing your visions

Leave a Reply

Fill in your details below or click an icon to log in: Logo

You are commenting using your account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s